- The Shark Guard with dust port
- Adjustable Clamp assembly
- 2 Shark Splitters
- 1 Shorty Splitter
- Ratchet handle
When you receive your Shark Guard, verify that nothing was damaged in shipping. Here is a current (7.0) list of parts that should be included with a standard JTAS-10 package.
| |
| This following information is basically the same for all the non spring loaded Shark splitter design. These are very simple devices and install much like the original splitters do, except for the fact that they only use one mounting point. These instructions would be the same on the Grizzly's, Generals, Deltas, Shop Foxes, some Jets and other. The main difference is that some of these splitters have tabs bent on the lower portion and some have notches. They all basically attach using the orange ratchet handle to replace the original splitter mounting bolt. I do not include a printed set of instructions in the Shark Guard packages. My thoughts are that would take more time and money. Since you are using the internet now, just become familiar with this page or print them out now. If you have any questions at all, please just email me. I am rarely caught by the phone. | |
| Lets start with the Shark Splitter, since this is the heart of this guard system and will be used most often. I suggest you apply some Johnson's Paste wax or Minwax Paste wax to both the larger Shark Splitters and the Shorty Splitter. This should be done periodically to clean the splitters and to slick up the surfaces to reduce friction. Disconnect the power source. Never count on your switch alone to control the power when working on machinery. They can and do fail. Currently, these splitters are designed to mount very much like the front portion of your OEM blade guard. It utilizes the mounting bolt and splitter boss inside the throat plate and behind the saw blade away from the operator. Remove your throat plate. It may also be easier initially to remove the saw blade as well. This would be a good time to clean out the inside of your saw. Remove any splitter that you have mounted now, by removing the 5/16-18 mounting bolt and washer. This thick washer will be used under the new orange ratchetting handle that came with the shark package. Now you need to install this handle. It has a threaded stud on it. Start threading the handle into the boss mounting hole. This handle works by turning, pulling out, and turning more. It is spring loaded and will snap back into gear without any outward pressure. It is kind of tricky to install the first time, but won't need to be removed, only loosened in the future. A hex head wrench may be useful to assist with installation of this quick release handle. Don't tighten this up completely. Slip the bottom portion of the Shark Splitter behind the large washer and onto the stud of the ratchet handle. You may notice that these splitters have a bent tab at the front of the mounting portion. This helps to insure that the splitter will stay where it should and not be able to tilt forward or backward. You can raise it up some, but I suggest that you mount it until the rear notch on the splitter is about 1/16 in. off the table or as close as possible without actually touching. You can now tighten up the handle on the splitter. Your installation should look similar to the photo on the right. When installed and tight on a splitter, you should move the ratchet handle to a forward or down position by pulling out on it, then releasing it in the correct position. This will prevent interference with the throat plate when tilting the blade fora bevel cut. |   |
| At this point of setup you will need to align or verify alignment of the splitter to the blade. Install your blade if you have removed it earlier. You will need to use a straight edge, steel ruler, framing square or something similar. The splitter needs to be completely in the shadow of the blade. If you looked from the front of the blade dead on at the blade while squinting, you should not see the splitter at the sides of the blade. Alignment can be accomplished a couple different ways. Here is a link to the online Operator's Manual for the Jet JTAS-10 right tilt table saw. Online Owners Manual in PDF format. The splitter alignment instructions are on page 9. I also offer brass blade shims here on the site that will help you to align the blade to the splitter instead of messing with the mounting bracket. Click the image to the right for a Flash File to see how these might be used. |  |
| Your Shark Guard comes with a shorty splitter. It may look a little different than this photo. This is to utilize when you can't have the larger splitter or the guard in place. Removal of the guard and splitter is a necessity for doing some sawing operations on your saw. This short splitter is also helpful in the prevention of kickbacks. It serves two functions. It helps to prevent the saw kerf from closing in on itself and grabbing the rear teeth of the blade. It assists in maintaining the width of the stock from the fence to the blade and helps prevent twisting of this stock into the rear teeth of the blade. You can now install your throat plate. |   |
| These come installed already, but if you need to remove or reinstall or otherwise work on them, here is some information an images that should help you do that. Installation for anti-kickback pawls. |
  |
| Here are a couple exploded diagrams of an 8.0 and better clamps. The larger bushings on an 8.4 go to the left side. The curves on the bottom of the clamp halves are at the front. Plain bronze bushings are on the rear bolts. Machined brass bushings are on the front bolt. It will be basically the same setup without pawls. |
  |
| This 6.0 version shipped with four separate splitters. The 7.0 versions are only shipping with three. This is done so that you can set the height of the Shark guard by changing the splitter. One splitter is for use with the thickest stock. On a 6.0, one is used for two inch and thinner stock. The next is for one inch and thinner. On the 7.0 version, the middle size is for about 1.5" and thinner stock. Then there is the shorty splitter for use when you can't use the guard. If you have or are wanting anti-kickback pawls included, the info on them is here. In these images below, you can see how the position of the splitter and blade is adjustable in the guard. Your blade can be to the right side or left side or centered up under the guard by moving the shims on the studs. This allows you to get closer to the rip fence when making narrow rips. A 3/4" rip would be possible if you used a good narrow push stick. Other places sell narrow aluminum push sticks. They may work fine, but I haven't used any of them. This one is specifically designed to be used with the Shark Guard. They have wooden handles and the angle and length make them an ideal accessory for the Shark. You can see the Shark Feeders here. These are also powder coated to match your guard. |
     |
| I have had two different styles of decals. The first type is self adhesive type. The decals come in two parts. The mouth and the eye. If you are looking at the shark from the front, the decals go in on the left side. I like to use Windex (any glass cleaner) and a soft cotton cloth like a T-shirt to clean the guard first. It may help to look at a photo like this one below. Remember, you are looking at the reverse side in this image. This was done so that you wouldn't have to handle the decal when moving the shark. It also gives is a nice appearance from the outside of the lexan. Next I spray a little pool of Windex where the decal will go. Then I peel the backing off the decal (can be difficult at times) and place the decal on the Windex. I hold it in place and start gently pressing the windex and air bubbles out from under the decal. Once all the air bubbles are out, that one is done. Repeat for the other. If you need to position the decal, it is easy before it's stuck. You can lift a corner and apply more Windex. You should be able to reposition it then.  The second type is water slide decals. Below are the instructions for those. These are the newer ones. They have a white opaque backing. You will only be needing to do step 5 and 6. * Step #1: Design your decals using any graphic software program. (Use 8 1/2 " x 11" sheet INK JET Decal Paper or cut sheet into half if desired.) * Step #2: Set your printer as follows: o Resolution = Best o Paper = Photo Gloss o (Print your decal on the glossy side of INK JET Decal Paper.) * Step #3: Spray your printed sheet evenly with Krylon Acrylic Crystal Clear High Gloss spray until the sheet has a shine (2-3 coats). Allow 30 to 60 minutes to dry and set. (This product is available at any craft or hardware store such as Lowe's, Home Depot, Ace Hardware, Walmart, etc. Any acrylic clear coat spray will work.) * Step #4: Cut out your image using a standard pair of sharp household scissors. * Step #5: Place decal into a cup of clean water for 45-60 seconds and remove when the thin decal film begins to slip along backing. (Discard backing material after the decal has been removed) * Step #6: Apply decal to clean surface; ceramic, glass, metal, plastic, soap, candles, mylar balloons, model trains, planes, cars, etc. Here is a link to a PDF file that you can print out. It will help you get the proper placement for these. Just print page two. Lay the guard down on the image and then you will be able to place the decals on the inside where they should go. |
| Decal placement file. |
| Here are some initial photo's of the 4" port model. I have offset the port to the left side of the guard. I have also left the clamp where it was and extended the bushings on the left side to get the extra width. This guard is the same distance from the fence as the 8.0. 1" is the distance from the right side of the guard to the blade. The guard in these photo's is actually longer than the typical guards for a 10" saw. The smaller of the two is the typical length. The bigger one is for a new line of 12" saws that I am just finishing up. The Grizzly 5959. There will be an added $15 cost for these larger ports. More material and the 4" polycarbonate is not only much more costly, but also a heck of a lot harder to bend and install. Now I tested this with some mdf and my dust collector. I wasn't really expecting to get that much better result. I typically get a few crumbs after a cut with the 2.5 inch port. I couldn't find ANY crumbs after 4 cuts with a 4" port. So, I guess bigger is better. After quite a few field trials now, some guys have stated that perhaps the dust collection may be too good. It likes to suck up everything including small offcuts. This can be bad because the offcut may want to rattle around inside the guard dancing on the blade. I suggest that if you do use the 4 inch port, you also employ a blast gate to this hose and close it off some if you anticipate having thin strips or small offcuts. Open it fully for larger parts. Some guys have also had trouble getting the hose onto the port. The dust port is kinda confusing. The whole thing is welded in at an angle, but when I cut the top back parallel to the top of the shark, it looks straight again. It really isn't. I have made this illustration to show that you need to attach the hose to the port at an angle. Once the hose is over the port, then you can straighten it back up and install a clamp. It will be a tight fit. The port is welded in there pretty good and can take a little handling. See the illustration below. |
              |
| Below are a few photo's of how the tail hooks work. They are fairly simply and serve to keep the guard from coming off when not wanted. Simply raise the hook to remove the guard. Lower it down onto the stud when installing it. |
     |
| The Shark Guard has a horizontal hooked slot at the rear and a vertical slot further forward. These slots are the mounting slots for this guard. The hooked slots get hooked on the rear studs of the clamp. There is now a safety hook that slips down over the rear stud to keep the guard from coming off when not intended. You can see in this image that the guard can be left in the upward position by hooking only the rear slots and resting the guard on the front stud. This feature is beneficial when measuring between the fence and blade with a steel rule. The front slots just slip down over the front studs with care taken to use the smaller bearing surfaces. With this done and your red tail hook slide down into place, your blade guard is installed. It will seem to some that the guard isn't clamped down anywhere and only rides or sits on these studs. Can that be right? Yes, the guard itself isn't really fastened to the clamp in the normal sense. What does happen is it's locked onto the studs when you feed stock under the guard or when the blade height is low. In either case the guard can't be lifted up enough to remove it from the clamp while in use. Dust collection can be hooked up to the top of the guard or you can simply cap off the dust port. I suggest that something be done to the port though. If left open, you can get a fountain effect of sawdust right into your face. I will have caps that plug this port available soon. For a good fit with something that is readily available, spray paint tops will serve as a good cap for the dust port. You can even get color coordinated caps this way. Rockler, Woodcraft and other outlets sell a nice 2 1/2 inch clear flex hose that fits this dust port well. It is a fairly snug fit by itself, but can be clamped down as well. I like leaving mine as a slip fit, because I utilize the same overhead hose for my router table. There are numerous ways the you can support the hose for the dust collection. On my Gallery page, you will see some photo's of different setups. On my Review page, you will find links to individual websites where some owners used varied methods of supporting this hose. |  |
| © 2002-2011 Lee Styron All Rights Reserved | Got Questions? E-mail Me |